KINAX ANGULAR LINEAR POSITION TRANSDUCERS

KINAX WT-710 Angular Position Transducer

The KINAX WT 710 Angular Position Transmitter converts the angular position of a shaft
into a load-independent direct current signal, proportional to the angular position. 
The unit is contact free. 
The compact housing has made this unit ideal for building onto other equipment and plant. 

• Non-Contact, Vibration Resistant Technology
  Outlasts Potentiometers
• Any Angle, 10º-270º with up to 60% Adjustability
• Output Signals from 0...1mA to 0/4...20mA
• Shaft Diameter: 2mm, 6mm, ¼"
• Intrinsically Safe Versions Available
• Typical Applications: Valve Position, Cutting Blade
  Angle, Water Cannon Position

• Measuring input: Angular position range limits 0...5° to 0...270 °

• Measuring output: DC current signal (load-independent, 2-, 3-or 4-wire connection)

• Potentiometer for adjusting span / Optimum matching of desired measuring range

• Direction of rotation: Output signal increases for clockwise or counterclockwise rotation

• Capacitive scanning system / No wear and low annual maintenance

• Low influence from bearing play, < 0.1%

• Accuracy ≤ 0.5% for ranges ≤ 150°

• Torque < 0.001 Ncm

• Drive shaft fully rotatable without stops at instruments without additional gear

• Available with type of protection "Intrinsic safety" EEx ia IIC T6 / Can be mounted in
  hazardous areas

• Unit in field type housing / Compact for building onto other equipment and plant

Measuring transmitter with contactless, capacitive sensing system for acquiring the angular position of a shaft. A load-independent DC-signal with a range of 4 to 20 mA is read out from the measurement output. It is especially well suited for surface mounting to equipment and apparatus thanks to its compact design.

• Measuring range, direction of rotation, characteristics, output changeover and other functions can be programmed via PC: facilitates planning and project work, short lead times, minimal inventory

• Angle of rotation measuring range: 0°...10° to 0°...50° or 0°...50° to 0°...350°

• Measurement output (measuring/supply circuit) utilizes 2-wire connection (4 to 20 mA signal)

• Adjustment of mechanical position and fine adjustment of the analog output, zero point and span may be set independently

• Programmable output characteristics: linear, V-characteristic or freely selectable linearization curve

• Shaft can be turned through full

• Serial interface

Measuring transmitter with contactless, capacitive sensing system for acquiring the angular position of a shaft.
A load-indepent DC-signal with a range of 4 to 20 mA is read out from the measurement output.
The robust housing has made this unit ideal for machines, ship building, transport, construction of vehicles and in the chemical industry.

• Measuring range, direction of rotation, characteristics, output changeover and other functions can be programmed via PC: facilitates planning and project work, short lead times, minimal inventory

• Angle of rotation measuring range: 0°...10° to 0°...50° or 0°...50° to 0°...350°

• Adjustment of mechanical position and fine adjustment of the analog output, zero point and span may be set independently

• Programmable output characteristics: linear, V-characteristic or freely selectable linearization curve

• Shaft can be turned through full, no damage occurs even if the upper limit value of the measuring range is exceeded

The KINAX WT 707 Heavy Duty Angular Position Transmitter converts the angular position of a shaft into a load-independent direct current signal, proportional to the angular position. 
The unit is contact free. 
The robust housing has made this unit ideal for machines and ship building.

• Impact and Vibration Resistant IP67 Housing
• Dual Cable Glands for AC Power Supply
• High Load rated 19mm Input Shaft
• Direct Replacement for KINAX 7W1
• Gear Box Ratios up to 1600:1 (optional)
• Intrinsically Safe & Marine Versions
• Typical Applications:
  • Power Generation: Turbine Vane, Damper & Gate, Heavy Duty Valve Position
  • Marine and Ship Board Applications: Rudder, Stabilizer, Thruster Position
  • Manufacturing: Roller Position, Aluminum
    Processing

• Measuring input: Angular position Range limits  0...5 to 0...270 °

• Measuring output: DC current signal (load-independent, 2-, 3- or 4-wire connection)

• Potentiometer for adjusting span / Optimum matching of desired measuring range

• Direction of rotation: output signal increases for clockwise or counterclockwise rotation

• Capacitive scanning system / No wear and low annual maintenance

• Continuous shaft rotation / No damage when overshooting angle measuring range

• Available with type of protection "Intrinsic safety" EEx ia IIC T6 /Can be mounted in
  hazardous areas (see Data on explosion protection")

• Ancillary unit in ruggedized housing / Vibration and shock-resistant, for applications on
  large machines and in ship building

• Marine version also available as per Lloyd’s Register of Shipping

The Linear position feedback transmitter KINAX SR 709 is used to measure and transmit linear displacement (stroke) on various types of control valves and other control devices. 
The output is a load independent DC signal. 
The position feedback transmitter consists of a KINAX angle transmitter and a reduction gear
which converts a linear movement into an angle of rotation of 0 … 90°. 
Both parts are contained in a robust cast aluminum housing. 
The mounting part to the control valve is based on NAMUR recommendations, (standards working group for measuring and process control in the chemical industry).

• Adjustable Stroke Range: 0...10mm to 0...140mm 
  (0...1/2"to 0...5 ½")
• IP54 Housing for Harsh Environments
• Intrinsically Safe Versions available

The pick-up of the stroke movement is made by means of a slotted lever. 
The adoption to strokes between 10 and 140 mm is made with an external lever transmission and by an internal gear ratio. 
The external lever transmission can be adjusted in such a way, that the internal cam shaft makes an angle of rotation of approx. 90° for a full stroke. The measuring range of the built-in angle transmitter KINAX 3W2 then corresponds with this angular rotation of 90°.

• Measuring input: Movement, stroke range limits  0 … 10 to 0 … 140 mm

• Setting of the measuring range is achieved via adjusting the lever system pivot point. More precise calibration is via zero and span potentiometers / Optimum adjustment of zero and span can be made to meet individual requirements

• Measuring output: DC current signal (load-independent, 2, 3 or 4-wire connection)

• Capacitive scanning system / Non-wearing 

• Unit in field type housing in cast aluminum with NAMUR mounting part for fitting to control valve

• Available in type of protection «Intrinsic safety» EEx ia IIC T6 / Can be mounted within the hazardous area (see Data on explosion protection")