SINEAX HEAD MOUNT TEMPERATURE TRANSMITTERS

SINEAX VK 616 HEAD MOUNT TEMPERATURE TRANSMITTER

SINEAX VK 616 is a two-wire head-mounted temperature transmitter. It is designed for measuring temperature in combination with thermocouples or resistance thermometers. 
Thermocouple nonlinearities are automatically compensated. 
The output signal is a current in the range 4…20 mA. The input variable and measuring range are programmed with the aid of a PC and the corresponding software. 
The sensor circuit is monitored for open and short-circuits and the output responds in a defined manner if one is detected. 
The power supply of 12…30 V DC is connected together with the signal by the two leads connected to the measurement output (loop powered).

• PC Programmable

• RTD and TC inputs

• Two, three and four wire connection

• Programmable Sensor Fault Response

• Isolated and Non-Isolated Versions

• 12-30 VDC Loop-Powered

SINEAX VK 626 HART HEAD MOUNT TEMPERATURE TRANSMITTER

SINEAX VK 626 is a two-wire head-mounted programmable temperature transmitter. It is designed for measuring temperature in combination with thermocouples or resistance thermometers. 
Thermocouple non-linearities are automatically compensated. The output signal is a current in the range 4…20 mA. Measured variable and measuring range are programmed using a PC with a suitable interface and running the programming software. The sensor circuit is monitored for open and short-circuits and the output responds in a defined manner if one is detected. 
The power supply of (12…30 V DC) is connected together with the signal by the two leads connected to the measurement output (loop powered).

• PC Programmable

• HART Protocol

• RTD and TC inputs

• Two, three or four wire connection

• Programmable Sensor Fault Response

• Isolated

• 12-30 VDC Loop-Powered

SINEAX VK 636 PROFIBUS-PA HEAD MOUNT TEMPERATURE TRANSMITTER

The SINEAX VK 636 is a head-mounted temperature transducer for use in automation systems with PROFIBUS.
It converts the measured value, i.e. the signal from a thermocouple or a resistance thermometer to the PROFIBUS-PA format.
PROFIBUS-PA (Process Automation) is an open field bus standard according to EN 50 170 and IEC 61 158-2 that requirements of the process industries. Both the communication and power supply are via the bus conductors. The measured variables, ranges and other parameters can be configured and set on a PC (Master Class 2) running the respective configuration software.

• PC Programmable
  PROFIBUS Process Automation Protocol
  RTD and TC inputs
  Two, three and four wire connection
  Programmable Sensor Fault Response
  Isolated

SINEAX PT 602 DIN MOUNT TEMPERATURE TRANSMITTER

SINEAX PT 602 is a DIN Mount configurable temperature transducer for PT100, 1 or 2-channel.
Measuring transducer for the conversion of the resistance value from a Pt 100 sensor into a linear temperature output signal. Depending upon utilized variant, 2, 3 or 4-wire connection can be used for the Pt 100 sensor. 
Measuring ranges can be set as desired with DIP switches and potentiometers.

• Measuring ranges can be configured as desired with DIP switches and potentiometers

• Indication of open-circuit sensor or short-circuit with red LED

• Electrical isolation between measurement input, measurement output and auxiliary power

• Power supply: integrated AC-DC power pack with large tolerance range

• Housing:
  SINEAX: S17 housing for top-hat rail or wall mounting

Input set to 0 ... 100 °C, output set to 4 ... 20 mA. 3-wire connection. Setting for 2-wire connection with DIP switch S1 and additional jumper, cable resistance of up to 50 W is possible. Additional temperature ranges from – 170 to + 800 °C can be configured with DIP switches, fine balancing with “Zero” and “Span” potentiometers.