HIGH-SPEED Hardware
GALEP-5D is uncompromisingly designed for speed.
The programming algorithms run on an internal 200 MIPS ARM-9
processor under Embedded Linux. The processor directly controls
the pin drivers via up to 4 FPGAs, which ensure the perfect
adaptation of the components to the programming algorithms. The
FPGAs (user-programmable logic) allow the realization of State
Machines, UARTs etc. and thus support time-critical components
that wouldn't be programmable at all with pure software
solutions. The programming cycle times are extremely short,
close to the specified minimum times of the components.
The internal 128 MB RAM serves as data storage and allows you to
transfer the data only once for programming multiple devices.
240 universal pin drivers
A universal
pin driver circuit especially designed for
GALEP guarantees optimal signal quality for the component to be
programmed. Each of the 48 pins carries the following signals:
Logical high, adjustable
between 1.3V ... 5.0V
Logical input, threshold adjustable between 0.5V … 5.0V
Three independent programming voltages up to 25V
Ground
Three switchable resistors for pullup and pulldown
Adjustable clock rate
The switching regulators for
the programming voltages are controlled by D/A converters in 100
mV steps. Further D/A converters are used to control the logic
levels (1.3V ... 5.0V) and the input threshold (0.5V … 5.0V).
All voltages are permanently monitored by an independent
coprocessor.
A universal pin driver
concept with as many pins as possible reduces the requirements
of adapters and thus ensures an overall low cost programming
system.
Standalone Mode
This feature is currently in development and will be available
in the next months as a free update. It allows using GALEP-5D in
mass production without a PC!
The programming data can be stored on SD card or on a local
server connected via Ethernet.
For programming multiple
components, several GALEP-5D devices can be controlled
simultaneously (cluster- or gang-programming).
In System Programming
The signals for in-system programming (ISP) can be taken from a
separately available ISP adapter or directly from the 48-pin ZIF
socket. The help system provides information about the wiring of
the target system for all supported components.
Software
GALEP-5D continues the established concept of the GALEP-32
software.
The program runs under Windows 95, 98, ME, NT4, 2000, XP, and
Vista. it features a comprehensive set of basic functions such
as read, program, compare and delete, along with easy-to-use
custom configuration options for any special functions required
by the selected component.
The editor allows a multitude of
functions for editing component contents which can be saved and
loaded in binary, intel-hex, motorola-s or jedec file format.
Mass production is supported by providing statistics functions
and serial number generation.
JTAG Support: Delete, program
and verify components with JTAG interface (joint test action
group, IEEE Std. 1149.1 ). The following formats are supported:
SVF-Script in XSVF(Xilinx) format; JAM byte code player (ALTERA).
The software is permanently
improved for supporting new components.
If you need a certain device that's not yet supported, use our
free Device on Demand Service.
Free updates are available.
Security
Prior to each function, GALEP checks the power consumption,
correct positioning, and the contacts of all pins of the
selected component. This prevents accidental damage to the
component or the device.
Modules and Adapters
GALEP-5D comes with a DIL-48 module and programs all components
in DIL sockets of up to 48 Pins between 300 … 600 MIL (ca. 7,5 …
16 mm) wide, without additional adapters. All GALEP-4 and
GALEP-5 adapters can be used with the DIL-48 module of GALEP-5D!
A main advantage of GALEP-5D
is the unique module concept. The DIL Module can be
replaced in seconds with a module for a different socket.
Modules for all sockets up to 240 pins are available. This keeps
the costs for the overall system low: F.i. a single QFP-120
GALEP-5D module replaces all 5 Fujitsu QFP-120-adapters for
GALEP-4, and additionally can program all other devices in the
same socket! When frequently programming components with high
pin numbers, a GALEP-5D has quickly brought in its price.
Technical Specifications
Format: ca. 118x172x22mm (+7mm socket)
Weight: ca. 750 g
DIL Module with 48-pin ZIF socket
Up to 240 universal pin drivers
Programs low-voltage components down to 1.3V
Mini USB 2.0 high-speed port
Ethernet 10/100 port
SD memory card slot
200 MIPS ARM-9 RISC processor, 128 MB RAM, 8 MB Flash
Up to 4 FPGAs (50K gates, 64Kb RAM)
3 linear voltage regulators for internal power supply
4 switching regulators for programming voltages
2 linear voltage regulators for logic levels and input threshold
2 Microcontrollers for internal voltage monitoring
8-channel D/A converter, 16-channel A/D converter
Embedded Linux 2.6 inside
Robust aluminum case
Kit contains
GALEP-5D device
DIL-48 module
Ethernet & Mini USB cables
AC adaptor
CD with manual and software
System Requirements
PC or Laptop with Pentium Processor
Windows 95 / 98 / ME / NT4 / 2000 / XP / Vista
USB 1.0 or USB 2.0 port, or Ethernet port
