Toll Free: 866-436-2430                     Email: sales@hotektech.com

 
 
Instruments, calibrators, standards, analyzers, dataloggers. analyzers
 
  Test measurement instrumens. Analytical instruments, ph meters, dissolved oxygen meter, hygrometer, salinity meter, weather instruments. Power analyzers, Gas combustion analyzer, Electronic load, Harmonic analyzer. Pressure calibrator, deadweight tester, temperature calibrator, current loop calibrator. Temperature datalogger, humidity datalogger, barometric pressure datalogger, wireless datalogger. Hygrometer, humidity datalogger, HVAC instrument, humidity controllers transmitters. Candela meter, Luminance meter, Radiometer, Albedometer, Luminance transmitter. Cable detectors, coil tester, insulation resistance, resistance bridge, tachometers. Digital multimeter, clamp on meter, amperometer, current meter, high line voltmeter, phasing sequence meter.  
  Resistance bridge, ohmmeter, insulation resistance meter, multimeters, milli ohmmeter, micro ohmmeter, megohmmeter. Manometer, Pressure gauge, deadweight tester, pressure pump, vacuum pump, pressure calibrator. Simulator, Calibrator, resistance standard, resistor decade, inductance standard, thermometry standards. Thermometry bridge, precision thermometer, infrared thermometer, temperature calibrator, dry block calibrator. Current transmitter, Luminance transmitter, energy transmitter, pressure transmitter, temperature transmitter.  
 

Search  

 
 
 

LCR CAPACITOR COMPONENT TESTER BRIDGE


DB210 Component Bridge Tester is a fast and accurate CLR Bridge offering the Component users the speed, accuracy and reliability required to test and sort a wide spectrum of passive components.
The DB210 can be used as stand-alone-instrument by using the display and keyboard. Further is the
instrument suitable for remote controlled, integrated test system. The instrument has IEEE 488 and
RS232C interfaces as well as Ethernet connector for easy PC control via a standard Web Browser.
External trig and BIN outputs are part of the standard design as well.

 DB210 LCR Component Tester

DB210 LCR Component Tester
Our Price: Contact us for pricing
Phone: 253-927-6186
866-318-6186
Fax: 253-927-6189
email: sales@hotektech.com

Test Fixture
A 4-terminal (Kelvin) test fixture JIG32 can be supplied in case that the DB210 should be used as a bench instrument.
The 4-terminal test fixture will effectively cancel all errors due to contact resistance and connecting cable impedance.
The JIG32 has gold plated contacts, and up to 1meter long cables can be connected between the test fixture and the DB210 without any deterioration of the accuracy.

Measured Parameters: C, L, R, (serial or parallel)   Tan d, ESR, Rs, Rp, L/Q,
Measuring Frequencies: 100kHz, 10kHz, 1kHz, 100Hz and120Hz selectable from the keyboard or by data-link
Measuring Voltages: 1 V RMS down to 40 Ohm
0,3 V RMS from 40 Ohm to 4 Ohm
Linear reduction at lower impedance values
Measuring Speed: 100Hz 120Hz 1kHz 10kHz 100kHz
From trig to end of measurement
 
180ms 180ms 38ms 38ms 38ms
From trig to data ready: 190ms 190ms 46ms 46ms 46ms
Add. time per meas. by average 160ms 160ms 34ms 34ms 34ms
Measuring Cables: 1m (39.3 inch) from bridge to fixture
Bias Voltage External: Up to ±48V DC
Accuracy C & tan δ: Frequency 100Hz &120Hz 1kHz Accuracy ±1 digit
Capacitance Tan d
  100pF - 300µF 1pF-99pF 0,5pF* ± .0010
100pF-389pF 0,1% ± .0005
390pF -  3µF 0.05% ± .0005
3mF  -  30µF 0.1% ± .0010
  >3mF C: (C measured / 0.3mF) * 0.1% Tan d: (C measured / 0.3mF) * 0.005
  10kHz 100kHz *) Accuracy ± 0,2pF
  39pF - 3µF 39pF - .3µF 0,05% ± .0005
Bin Sorting: Up to 12 limits for 1st parameter and 4 limit for 2nd parameter by opto-couplers
Interfaces Rear panel: IEEE 488 (GPIB), RS232C and Ethernet connector
Control: Measure end, data ready, trig ready, fault and status
Trig input DC, AC and contact closure
Keyboard & Display Front panel: For manual settings, etc
Environment: Ambient temp.: 10-30 degrees Celsius
Warm-up time: Minimum 30 minutes
Power: 90-130 and 200-260 V AC, 50-60 Hz,
Calibration Interval: Minimum: Every 12 months
 

Please email sales@hotektech.com or call 253-927-6186 if you are interested in a purchase, or
  need additional information.

[Home] [Top] [Distribution] [Contact Us]