|
Specifications
Megohmmeter DB621:
|
|
RESISTANCE
MEASUREMENTS:
|
|
|
Range:
|
10 kOhm to 1 POhm
(dependent on test Voltage)
(Peta = 1.000.000 Giga)
|
|
Accuracy for all
Megohmmeters:
|
Rx< 20 GOhm x
Vtest:
± 2% of value
Rx> 20 GOhm x
Vtest: ±Vtest/1pA in Ohm,
max reading Vtest/0.1pA
|
|
|
DC CURRENT
MEASUREMENTS:
|
|
|
Range:
|
1 pA to 1 mA
|
|
Accuracy:
|
±2% of value ±1pA
|
|
DISPLAY READING
|
|
|
Direct reading:
|
Current or Amperes,
3,5 digits
|
|
Bar Graph:
|
8 ranges with 2
decades per graph with fixed- or autoscaling
|
|
x – y Graph:
|
Current or
resistance scale versus time scale
|
|
INPUT RESISTANCE:
|
10 kOhm for I
test> 10nA / 1 MOhm for I test< 10nA
|
|
Discharge
Resistance:
|
10kOhm
|
|
TEST VOLTAGE
|
|
|
Range:
|
10 V to 1000V in 1 V
steps
|
|
Accuracy:
|
±2% of value or ±1
Volt in un-calibrated mode
|
|
Stability:
|
±20 ppm/degree C
|
|
Source Resistance:
|
150
Ohm
|
|
Max currents:
|
Measurement: 2 /
25mA Pre-charge: 100mA
|
|
Switching:
|
Manually ON/OFF
from front panel or controlled by a built-in timer, or by remote
control.
|
|
TIMING:
|
Programmable Fast
Charging:
0 to 9999 msec (charge resistance 200 Ohm)
|
|
Programmable
Measurement delay:
|
0 to 9999 msec
|
|
Discharge Time:
|
t = 0.1 x Cx (in µF)
with Vtest decreasing to 1 % of test level
|
|
MEASURING SPEED:
|
|
|
Trig Mode:
|
One Measurement:
<52 msec (excl. charging)
Average up to n = 100measurements: <52 + (N-1) x 40 msec (excl.
charging)
|
|
Continuous Mode:
|
Direct Reading: 90
to 4000 msec depending on average
Bar Graph: Display update every 52 msec
|
|
STANDARD FITTED
INTERFACES:
|
|
|
LIMITS:
|
5 built-in
programmable limits on resistance or current
|
|
IEEE 488: (IEEE
488-1 and 2)
|
"Talker
Only" and Talker/Listener" Modes. True sub-set of
Standard protocol
|
|
RS232C:
|
Baud rate up to
19,200 Baud. Full two-way control/output
|
|
Control I/O:
|
Opto-coupler input
/ output 25 V/10mA. Trig, Measure END Signal, Trig Ready Signal,
Data Ready Signal, Fault Signal, Limit Outputs
|
|
Ambient
Temperature:
|
10 –40 degrees
Celsius
|
|
Power:
|
90 – 130 and 200
– 260 V AC 50 – 60 Hz
|
|
DIMENSIONS:
|
|
|
Height:
|
140 mm/ 5.5 inch
|
|
Width:
|
438 mm/ 17.2 inch
|
|
Depth:
|
360 mm/ 14.2 inch
|
|
Weight:
|
16.5 kg/ 36.3 lbs.
|
|
ACCESSORIES
SUPPLIED:
|
Line power
connector, Two 1.5 m coax cables with H.T. BNC connectors
Brackets for 19" rack-mounting, Manual in English
|
|
Options:
|
|
Item no:
|
|
|
Higher measure
current
|
No
|
|
|
|
Fixture for axial
and radial components:
|
Yes
|
|
|
|
Fixture for SMD
comp. requires Jig 600
|
Yes
|
|
|
|
Test probe with
trig contact:
|
Yes
|
|
|
|
ALL SPECIFICATIONS SUBJECT TO CHANGES WITHOUT PRIOR
NOTICE
|
