All ProductsAnalyticalAnalyzersCalibratorsHumidityData LoggersLight MetersMeasurement

 

MultimetersOhmmetersPressureStandardsTemperatureTransmitters

PARALLEL TUBE LIQUID TEMPERATURE BATHS
Models 915 Parallel Tube Liquid Baths Temperature range from -65°C to +300°C.

Neptune 915H Parallel Tube Liquid Bath. Temperature range 5°C above ambient to 300°C
Neptune 915MWE Parallel Tube Liquid Bath. Temperature range
-30°C to 300°C
Neptune 915LW Parallel Tube Liquid Bath. Temperature range
-65°C to 300°C

The 915 Parallel Tube Liquid Bath is, no question, the finest stirred liquid parallel tube bath produced.
Typical uncertainties of measurement are less than ±0.0005°C over the complete 
temperature range of -65°C to +300°C.

Model 915 - NEPTUNE Parallel Tube Liquid Bath
Parallel Tube Liquid Bath

The 915 Liquid Bath has a wide temperature range using 
silicon oils and other suitable liquids. 

All components in contact with the liquid 
are of stainless steel and are insulated with 
materials which are completely safe in use. 

The 915 used in conjunction with a chiller, 
utilizes the latest ozone friendly gases.

The Model 915 Parallel Tube Liquid Bath is a development of the previous 815 model and has many features which enhance its performance and enable ease of operation. It is suitable for the calibration of Liquid in Glass thermometers, Industrial Platinum Resistance thermometers, Standard Platinum Resistance Thermometers, Thermocouples and Industrial Temperature sensors. 
It can also be used with fixed point cells.
The temperature range of the standard 915 liquid calibration bath (915H) is 40°C to 300°C. 
When the 915 is used in conjunction with our external chiller the low temperature 
limit can be extended to -65°C.

Liquids are circulated by a propeller which mixes and forces the liquid through a specially designed orifice in the rear of the two parallel tubes. A variable speed motor optimizes the flow as the viscosity of the liquid changes. Below the orifice plate liquid is circulated over a mineral insulated heater and temperature sensors which control the temperature of the bath. The liquid flows up the calibration tube and weirs over the tube into a collection tray where it returns to the rear tube for recirculation. 
An angled side entry tube enables a refrigeration cooling probe to be inserted in the rear of the two parallel tubes.

The temperature controller has resolution from 0.01°C to 0.1°C which auto scales to suit the four digit display (all digits can be read with the Cal NotePad Software). 
The 915 is fitted with serial communications for interfacing to a PC as standard.

With the high cost of some silicon oils the 915’s seven liter capacity makes it relatively inexpensive to fill compared to many other baths.

The changing of liquid is easily enabled by using the fitted drain. The design also allows for the expansion of liquids when being raised to a particular calibration temperature.

Model Types

915 H
915 MWE
915 LW

Standard Unit,
supplied with chiller 915-10
supplied with chiller 915-11

Temp Range

915 H
915 MWE
915 LW

5°C above ambient to 300°C
-30°C to 300°C
-65°C to 300°C

Accuracy

Using Fixed Point Cells ±0.0005°C
Mercury Triple Point, Water Triple Point,
Gallium Melt Point, Indium Freeze Point,
Tin Freeze Point

Vertical Profile

At extreme temperatures ±0.003°C
At close to ambient ±0.001°C

Temperature Stability
by Comparison

Direct in Liquid ±0.001°C
In Equalizing Block ±0.0005°C

Communication

Supplied as standard with serial interface, PC adapter
cable and Cal NotePad.

Liquid Capacity Approximately 7 liters
Working Volume 100mm diameter by 400mm depth
Overall Dimensions 1020mm x 580mm x 640mm (HxWxD)
Weight 45kg approximately
Power

1kW (excluding Chiller) 108-130 or 208-240V, 50/60Hz

Safety

Variable set-point over-temperature trip. Automatic over-fill protection tube

Please email sales@hotektech.com or call 253-927-6186 if you are interested in a purchase, or
  need additional information.

[Home] [Top] [Distribution] [Contact Us]