Toll Free: 866-436-2430                     Email: sales@hotektech.com
 
 
Instruments, calibrators, standards, analyzers, dataloggers. analyzers
 
  Test measurement instrumens. Analytical instruments, ph meters, dissolved oxygen meter, hygrometer, salinity meter, weather instruments. Power analyzers, Gas combustion analyzer, Electronic load, Harmonic analyzer. Pressure calibrator, deadweight tester, temperature calibrator, current loop calibrator. Temperature datalogger, humidity datalogger, barometric pressure datalogger, wireless datalogger. Hygrometer, humidity datalogger, HVAC instrument, humidity controllers transmitters. Candela meter, Luminance meter, Radiometer, Albedometer, Luminance transmitter. Cable detectors, coil tester, insulation resistance, resistance bridge, tachometers. Digital multimeter, clamp on meter, amperometer, current meter, high line voltmeter, phasing sequence meter.  
  Resistance bridge, ohmmeter, insulation resistance meter, multimeters, milli ohmmeter, micro ohmmeter, megohmmeter. Manometer, Pressure gauge, deadweight tester, pressure pump, vacuum pump, pressure calibrator. Simulator, Calibrator, resistance standard, resistor decade, inductance standard, thermometry standards. Thermometry bridge, precision thermometer, infrared thermometer, temperature calibrator, dry block calibrator. Current transmitter, Luminance transmitter, energy transmitter, pressure transmitter, temperature transmitter.  
 

Search  

 
 
 

DOCUMENTING MULTIFUNCTION CALIBRATOR HART


DMC-1400 Documenting Multifunction Calibrator
The DMC-1400 Documenting Calibrator fully documents any calibration easily while performing the normal job. No special software is required! It features the ability to test for pass/fail criteria, measure and simulate thermocouples, RTDs, current, voltage, and frequency, and source pulse trains.
In addition, the built-in 250 Ohm resistor for HART compatibility with smart transmitters and PLCs, full fuseless protection, and a serial communications port for full control with ASCII commands

Documenting Multifunction Calibrator

Documenting Multifunction Calibrator
 
Our Price: Contact us for pricing
Phone: 253-927-6186
866-318-6186
Fax: 253-927-6189
email: sales@hotektech.com
  • Maintain calibration data for 50 instruments in non-volatile memory

  • Print calibration certificates without PC

  • Communications port compatible with BetaPort-P pressure modules included

  • All source modes can be programmed with dedicated setpoints

  • Built-in 250 Ohm resistor for HART compatibility with smart transmitters and PLCs

  • Direct entry of custom RTD coefficients(R0,A,B,C)

  • Meets CE Requirements and is designed to IEC 1010 safety standards

Capture calibration data for 50 instruments with both AS FOUND & AS LEFT data
Measure and source T/Cs (13 types), RTDs (13 types), Ohms, current, voltage,
frequency; source pulse trains
IsolatedmA/V read-back circuit for complete transmitter calibration.
Pressure module communication port compatible w ith BetaPort-P digital pressure
modules
using optional BPPA-100 adapter.
Built- in 24 VDC loop power supply can drive 4 – 20 mA loops up to 1000 Ohms.
Direct entry of custom RTD coefficients (R0, A, B, C).
All source modes can be programmed with dedicated setpoints.
Highest accuracy
in class to ±0.015% of reading.
Meets CE requirements and is designed to IEC 1010 safety standards.

DMC-1400 Documenting Calibrator Specifications (23 °C ±5 °C unless otherwise noted) 
 

Voltage Read and Source
Source 0.000 to 20.000 VDC
Read
Isolated 0.000 to 30.000 VDC
Non-Isolated 0.000 to 20.000 VDC

Thermocouple mV
Read/Source -10.000 to +100.000 mV

Current (mA)
Source 0.000 to 24.000 mA
Read
Isolated 0.000 to 24.000 mA
Non-Isolated 0.000 to 24.000 mA

Frequency (1 to 20 V selectable
amplitude)
CPM Source and Read 2.0 to 600.0 CPM
Hz Source and Read 1.0 to 1000.0 Hz
kHz Source and Read 1.0 to 10.00 kHz

Pulse (Source only; 1 to 20 V
selectable amplitude)
Pulses 1 to 30,000.0
2 CPM to 10 kHz

Ohms
Source 5.0 to 4000 Ohms
Read 0.00 to 4000.0 Ohms

Thermocouple Read and Source
J Thermocouple -200.0 to +1200.0 °C
K Thermocouple -200.0 to +1370.0 °C
T Thermocouple -200.0 to +400.0 °C
E Thermocouple -200.0 to +950.0 °C
R Thermocouple -20.0 to +1750.0 °C
S Thermocouple -20.0 to +1750.0 °C
B Thermocouple +600.0 to +1800.0 °C
C Thermocouple 0 to +2316.0 °C
XK Thermocouple -200.0 to +800.0 °C
BP Thermocouple 0 to +2500.0 °C
L Thermocouple -200.0 to +900.0 °C
U Thermocouple -200.0 to +400.0 °C
N Thermocouple -200.0 to +1300.0 °C

RTD Read and Source
Ni120 (672) -80.0 to +260.0 °C
Pt100 (385) -200.0 to +800.0 °C
Pt100 (3926) -200.0 to +630.0 °C
Pt100 (3916) -200.0 to +630.0 °C
Pt200 (385) -200.0 to +630.0 °C
Pt500 (385) -200.0 to +630.0 °C
Pt1000 (385) -200.0 to +630.0 °C
Cu10 -100.0 to +260.0 °C
YSI400 +15.00 to +50.00 °C
Cu50 -180.0 to +200.0 °C
Cu100 -180.0 to +200.0 °C
Pt385-10 -200.0 to +800.0 °C
Pt385-50 -200.0 to +800.0 °C
Environmental
Operating Temperature -10 °C to +50 °C
Storage Temperature -20 °C to +70 °C
Stability ±0.005% of reading/°C outside of 23
°C ± 5°C
 

Power Requirements
6 VDC; Batteries 4 AA; alkaline or optional rechargeable

Mechanical
Dimensions 8.7” H x 4.2”W x 2.3” D
(220.9 x 106.6 x 58.4 mm)
Weight 30.5 ounces (863 gms)

Accessories Included
Test leads, 4 AA alkaline batteries, NIST Certificate, instruction
manual

Optional Accessories
Carrying Case, Model CC572

Accuracy (read and source unless otherwise noted)
Voltage ±0.015% of reading, ±2 mV

Thermocouple mV ±0.02% of reading, ±10 μV

Thermocouple RTD
(add 0.2°C for Cold Junction Compensation error)

Type J 0.2 °C Ni120 (672) 0.2 °C
Type K 0.3 °C Pt100 (385) 0.2 °C
Type T 0.2 °C Pt100 (3926) 0.2 °C
Type E 0.2 °C Pt100 (3916) 0.2 °C
Type R 1.2 °C Pt200 (385) 0.8 °C
Type S 1.2 °C Pt500 (385) 0.4 °C
Type B 1.2 °C Pt1000 (385) 0.2 °C
Type C 0.6 °C Cu10 1.4 °C
Type XK 0.2 °C YSI400 0.1 °C
Type BP 0.9 °C Cu50 0.4 °C
Type L 0.2 °C Cu100 0.3 °C
Type U 0.25 °C Pt385-10 1.4 °C
Type N 0.4 °C Pt385-50 0.4 °C

Current (mA)
READ                                 SOURCE
±0.015% of rdg ±2 μA         ±0.015% of rdg ±2 μA
CPM
READ                                 SOURCE
 ±0.05% of rdg±1 LSD         ±0.05% of rdg
Hz
READ                                 SOURCE
 ±0.05% of rdg ±1 LSD        ±0.05% of rdg
kHz
READ                                 SOURCE
 ±0.05% of rdg ±1 LSD         ±0.125% of rdg
400ohmRange
READ                                 SOURCE
 ±0.025% of rdg ±0.05ohm    ±0.025% of rdg ±0.05ohm
4000ohmRange
READ                                  SOURCE
±0.025%of rdg ±0.5ohm       ±0.025% of rdg ±0.5ohm
Ohms works with all pulsed transmitters down to 5 ms

Measuring Pressure with the DMC-1400
The DMC-1400 is compatible with BetaPort-P digital pressure modules using the BPPA100 adapter.
Please refer to the separate
Pressure Modules data sheet for module ranges and model
numbers DMC-1400 Preliminary Data Sheet 060803

Information and specifications are subject to change without notice.

 

Please email sales@hotektech.com or call 253-927-6186 if you are interested in a purchase, or
  need additional information.

[Home] [Top] [Distribution] [Contact Us]