Toll Free: 866-436-2430                     Email: sales@hotektech.com

  
 
Instruments, calibrators, standards, analyzers, dataloggers. analyzers
 
  Test measurement instrumens. Analytical instruments, ph meters, dissolved oxygen meter, hygrometer, salinity meter, weather instruments. Power analyzers, Gas combustion analyzer, Electronic load, Harmonic analyzer. Pressure calibrator, deadweight tester, temperature calibrator, current loop calibrator. Temperature datalogger, humidity datalogger, barometric pressure datalogger, wireless datalogger. Hygrometer, humidity datalogger, HVAC instrument, humidity controllers transmitters. Candela meter, Luminance meter, Radiometer, Albedometer, Luminance transmitter. Cable detectors, coil tester, insulation resistance, resistance bridge, tachometers. Digital multimeter, clamp on meter, amperometer, current meter, high line voltmeter, phasing sequence meter.  
  Resistance bridge, ohmmeter, insulation resistance meter, multimeters, milli ohmmeter, micro ohmmeter, megohmmeter. Manometer, Pressure gauge, deadweight tester, pressure pump, vacuum pump, pressure calibrator. Simulator, Calibrator, resistance standard, resistor decade, inductance standard, thermometry standards. Thermometry bridge, precision thermometer, infrared thermometer, temperature calibrator, dry block calibrator. Current transmitter, Luminance transmitter, energy transmitter, pressure transmitter, temperature transmitter.  
 

Search  

 
 
 

AG0201HV 200 WATT HV RF GENERATOR

AG0201HV RF, HV Amplifier Generator.
The AG0201HV HV RF Generator is unique source of RF high voltage suitable for a wide variety of applications in industry and research.
It combines a number of features to simplify establishments and control of gas plasma. 
A very accurate broad band power meter senses the power transfer from the power amplifier to the matching network and through it to a plasma discharge.
Our Price: Contact us for pricing
Phone: 253-927-6186
866-318-6186
Fax: 253-927-6189
email: sales@hotektech.com

ASP OPERATION

An accurate broadband power meter senses the power transfer from the power amplifier to the load. 
The Analog Signal Processor (ASP) monitors this transfer and maintains a safe operating condition for the AA03LF. Forward Power and Reverse Power levels (in Watts) are simultaneously displayed on the front panel in Watts. The ASP displays and controls all critical parameters of the amplifier. 
So it maintains an accurate, repeatable process control, and is user friendly as well.

The AG0201HV can be controlled in one of two ways: 
1. Manually from the front panel, and 
2. Remotely through the optional analog and digital interface port.
SPECIFICATIONS 
DESCRIPTION RANGE/CHARACTERISTIC
GENERATOR
Frequency Range 100 kHz to 500 kHz
Frequency Stability < 1% Full Scale
Power Output 0 - 200 W
Ignition Power > 200 W
Output Voltage 0 - 6 kVp (12 kVp-p); Settings up to 8 kVp (16 kVp-p available)
Output Impedance Designed for the best power transfer into high impedance loads
Output Protection Short and open circuit. Overvoltage on HV output.
Over temperature ( full range air control)
Load Mismatch Tolerance Continuous--unit protected against any output load conditions.
High Voltage RF Connection 48" of high voltage cable with alligator clips
(Other options available)
Metering Accuracy Power: ± 3% (Typical)
HV: Within 10% when operating into a matched load
Forward Power Regulation ± 1% of f scale
Line Regulation 0.5% at full power
Harmonic Distortion < -45 dBc (w/standard load @ 80 W FWD, 8 kVp-p)
Hum, Noise and Ripple < -40 dBc (on standard load @ 80 W FWD, 8 kVp-p)
Spurious Radiation Designed to meet FCC Part 18
CONTROLS/INDICATORS/INTERFACE
Front Panel Controls: Power, Frequency
Meters: Forward and Reflected Power
Indicators: AC ON, RF ON, Remote Control Enable, Overheat, HV Limit, FWD Power Limit, REV Power Limit
Rear Panel Connectors: AC Input, HV RF Output, Communication (DB 25), Options I/O (DB-15 w/options installed), Safety Ground (0.25" x 20 stud)
PRIMARY POWER
Input 100 - 120 Vac, +/-10%, 50-60 Hz, single phase; 200 - 240 Vac (Internal Jumper)
Current 400 VA @ Full Power Output (Approximate)
Circuit Protection Double-pole circuit breaker @ 10 A (Located on front panel)
Connector IEC Standard Power Entry; CE approved
GENERAL
Operating Temperature Range 32° - 113° F (0° - 45° C)
Humidity 80 %
Cooling Forced-Air
Acoustic Level 45 dBa @ maximum fan speed and maximum temperature
Dimensions 5.25" x 10" x 15" (H x W x L)
Weight 15.5 lbs (7.5 kg)
REAR PANEL CONNECTOR SIGNAL DESCRIPTION 
Analog and Digital I/O (Sub-D25 Connector)
PIN SIGNAL FUNCTION INPUT/OUTPUT  DESCRIPTION
1 REV LIMIT OUT TTL Compatible:
H = RF Out Limit
L = Normal operating condition at low VSWR

NOTE: This output indicates that output power level was automatically reduced under load mismatch condition.

2 REV METER OUT Linear voltage output, 1 Vdc = 100 W
3 FWD METER OUT Linear voltage output, 1 Vdc = 100 W
4 EXT RF POWER ON IN TTL Compatible:
H = Remote ON-Requested
L = Remote ON-Disabled
5 EXTERNAL RF PWR REF IN Linear voltage input: 5 Vdc = 200 W; 1 Vdc = 40 W
7 RF ON INDICATOR OUT TTL Compatible:
H = Generator ready to produce output
L = Generator RF section not ready
8 EXTERNAL CONTROL SELECT IN TTL Compatible:
H = Remote Control Active
L = Front Panel Control Active
9 HEAT SENSE OUT TTL Compatible:
H = HOT! Heat problem
L = normal operating conditions.

NOTE: This output indicates that over temperature condition has occurred.

10 INTERLOCK LOOP OUT Connect to external safety device swtich input.
~ 12 Vdc Source
11 POWER ON OUT TTL Compatible:
H = Power ON
L = Power OFF

DC power applied to control circuit. Indirect meaning: AC is ON.

18/19/21 SIGNAL COMMON
(Internal AGND)		 IN/OUT Connected to Internal Ground AGND
25 HV METER OUT Linear voltage input: 1 Vdc = 10 KVp-p

NOTE: High Impedance Output! Use meter with high impedance input for proper operation,

 

Please email sales@hotektech.com or call 253-927-6186 if you are interested in a purchase, or
  need additional information.

[Home] [Top] [Distribution] [Contact Us]