SINEAX V604 DIN Mount Programmable Transducer
The universal temperature transmitter SINEAX V 604 converts the input variable – a DC current or voltage,
or a signal from a thermocouple, resistance thermometer, remote sensor or potentiometer – to a proportional
analogue output signal.
INPUT: 0-2 mV to ±
40 V, 0-80 µA to –50-100 mA, Thermocouple, RTD, Thermistor, Potentiometer.
OUTPUT: 0-5 mA to ±
40 mA, 0-4 V to –12-+15 V
The analogue output signal is either an impressed current or superimposed voltage which is processed by other devices for purposes
of displaying, recording and/or regulating a constant.
Input variable and measuring range are programmed with the aid of a PC and the corresponding software.
Other parameters relating to specific input variable data, the analogue output signal, the transmission mode, the operating sense and the open-circuit sensor supervision can also be programmed.
The open-circuit sensor supervision is in operation when the SINEAX V 604 is used in conjunction with a thermocouple, resistance thermometer, remote sensor or potentiometer.
SINEAX Programmable universal Transducer
| Model | Description |
|---|---|
| SINEAX V604 | DIN Mount Programmable universal Transducer |
SINEAX VC 603 Universal Transmitter with alarms.
The combined transmitter alarm unit SINEAX VC 603 converts the input variable – a DC current or voltage,
or a signal from a thermo-couple, resistance thermometer, remote sensor or potentiometer – to a proportional
analogue output signal. It is also equipped with 2 limit contacts for monitoring the input variable.
INPUT: 0-2 mV to ±
40 V, 0-80 µA to –50-100 mA, Thermocouple, RTD, Thermistor, Potentiometer
OUTPUT: 0-5 mA to ±
40 mA, 0-4 V to –12-15 V, 1 DPDT, 2 SPDT
The binary output signals of the two limit contact circuits are used for signaling out-of-limit conditions, control purposes and two-point regulation.
A considerable number of measuring ranges including bipolar or spread ranges are available. Input variable and measuring range are programmed with the aid of a PC and the corresponding software.
Other parameters relating to specific input variable data, the analogue output signal, the transmission mode, the operating sense, the binary output signals and the open-circuit sensor supervision can also be programmed.
Transmitter with alarms.
| Model | Description |
|---|---|
| SINEAX VC 603 | SINEAX VC 603 Universal Transmitter with alarms. |
SINEAX C402 DIN mount alarm unit
The alarm unit SINEAX C402 is normally applied to monitor the limits of both current and voltage
measurements.
The status of the device is signalled remotely by a relay and locally by LED’s.
The electrical insulation between input, output relay contacts and the power supply conforms to
IEC 1010.
The value detected by the alarm unit is set on a potentiometer and measured at test sockets on the front
of the unit.
The alarm unit fulfils all the important requirements and regulations concerning electromagnetic
compatibility EMC and Safety (IEC 1010 resp. EN 61 010).
It was developed and is manufactured and tested in strict accordance with the quality assurance standard
ISO 9001/ EN 29 001.
Production QA is also certified according to guideline 94/9/EG.
2 relay outputs, each equipped with one changeover contact.
Signal flow direction can be selected for relays and LEDs with jumpers.
Electrical isolation between measurement input, contact outputs and auxiliary power.
Power supply: integrated AC-DC power pack with large tolerance range.
Housing: SINEAX: S17 housing for top-hat rail or wall mounting SIRAX: B17 housing for plug-in installation to BP902 rack
SINEAX C402 DIN mount alarm unit
| Model | Description |
|---|---|
| SINEAX C402 | SINEAX C402 DIN mount alarm unit |